Product Categories in this Section
-
Bandai Area Radiation Tester Replacement LIGHT POD, Right Hand RED is now finally available. These light pods were created from molds made of the original toy parts. The brass contacts for the light bulbs are hand made of the same thickness and configuration of the original parts. The same wattage bulbs are installed and colored as original. Ample wire is supplied and will be trimmed to length when you install. It should be noted that the pods are designed to be installed in the same fashion as the original parts. Some skill is required to open the tin pod pylons (not included - you must have the original pylons). The pods are secured to the pylon by brass eyelets with a minimum length of approximately 3/16". Once mounted, the wiring for each pod is trimmed to length and soldered to the pylon electrical mount pins. Be sure to apply electrical tape over the solder connections before reassembling the two pylon halves. The pods are also available as a set for a discounted rate of $250.00.
-
Bandai Area Radiation Tester Replacement LIGHT POD, Left Hand GREEN is now finally available. These light pods were created from molds made of the original toy parts. The brass contacts for the light bulbs are hand made of the same thickness and configuration of the original parts. The same wattage bulbs are installed and colored as original. Ample wire is supplied and will be trimmed to length when you install. It should be noted that the pods are designed to be installed in the same fashion as the original parts. Some skill is required to open the tin pod pylons (not included - you must have the original pylons). The pods are secured to the pylon by brass eyelets with a minimum length of approximately 3/16". Once mounted, the wiring for each pod is trimmed to length and soldered to the pylon electrical mount pins. Be sure to apply electrical tape over the solder connections before reassembling the two pylon halves. The pods are also available as a set for a discounted rate of $250.00.
-
This is a replacement WIND UP KEY for the CIJ Alfa P2 Racer , made in France. All dimensions for the replacement were taken from an original key. The brass shaft diameter and the steel winding handle are of the same thickness as the original key. The length is correct and allows winding without interference or binding near the back wheel of the toy. If you look closely at the pictures, I also drilled and inserted a brass locking pin which secures the handle to the shaft, just as original. These can be ordered with black painted steel winding handle or aged patina. Please specify when ordering. These are in stock in both variations shown here. Make your Alfa complete with one of these rare keys.
-
This listing is for a reproduction of an early German (1953 - 1970) dash mounted mileage counter. These were quite often used with early Volkswagens and other European vehicles that didn't have gas gauges. I make these from a mold taken from an original disassembled counter. The original counter had a white counter shroud with black base and number wheels featuring white numbers.
-
The BIG CHIEF DELUXE bicycle light is hand painted in brilliant, vibrant multicolor. The 308 stainless steel mounting stem needs no extra care and secures easily to the bicycle's axel utilizing the wheel mounting nut, front or rear. The light has a 36" wire lead that attaches to a 'positive' battery lead and the mounting stem acts as the system ground. The lights to attach to both original tank bike lighting or dynamo light systems. Future editions of light pairs will be available as LED wireless installation. Coming soon, Uncle Al's Toys will introduce another version of the Big Chief light for your fender.
-
This is a replacement head for the 1939 Ideal Novelty and Toy Company, Superman composition toy/doll figure. This is the first known Superman toy and they are extremely rare and in high demand. This replacement head was created from a mold made of an original head. This resin cast replacement comes with a metal loop inside, just as original, so that it will accept the spring and metal hook that comprise the flexible joints of the legs. Please allow 14 days from the time of ordering and purchase as these are made to order.
-
This listing is for a metal replacement battery cover door that fits the Nomura battery operated Robby Space Patrol, the Moon Car - Moon Patrol Space Division #3 and the Moon Space Ship. This replacement door is a hand worked, three piece reproduction of the original cover and each one is fitted to a toy to ensure proper fit and function. The bottom of the toy needs to be accessible in order to properly attach the cover. The hinges come pre-bent for proper insertion and care must be taken when installing. The reason so many of these toys end up with missing covers is primarily due to the fragile design of the hinges. Once the hinges are inserted into the 'L' slots (working from the inside of the toy), the hinge pins that are bent at 90 degrees are straightened with a plier to form a 'T' shape, effectively locking the door in place. I use a duck bill plier to flatten the hinge completely. If you are uncomfortable opening up the toy, the door hinges can be carefully inserted into the 'L' shaped slots and then closed and latched but please note that this should only be done if you don't intend to insert the batteries. The cover, when inserted this way is only being supported by one half of each hinge. The battery weight will put too much pressure on the hinge and could break the pins. As you can see in the pictures, I've inserted a door into the bottom of one of my toys to test the fit of the door when the latch is engaged. Each door I make is tested in this fashion to guarantee an excellent fit for your toy. Other parts are available for this toy and will be listed soon.
-
Battery Box Marx Hootin Hollow Haunted House is a perfect fitting replacement tin part complete with battery contacts. Each battery box is test fit to an original toy rear panel to ensure an exact fitting installation. Just solder your wires and go! The battery contacts are slightly different than the original ONLY in that I have installed the flexible brass contact at both ends rather than the round stationary contact as original. The contact board is also gray vs. the original tan color. *Please note* You will see in one of the gallery pictures that I have installed 3 'D' Cell batteries in the new box. These are Heavy Duty batteries - NOT ALKALINE BATTERIES! Alkaline batteries did not exist at the time the haunted house and many other tin battery toys were made. Slightly dimensionally larger than the heavy duty batteries, it explains why so many vintage toys with either tin OR plastic battery boxes have damaged battery boxes. Always remember, NO ALKALINE BATTERIES IN ANTIQUE/VINTAGE TOYS! Marx Hootin’ Hollow Haunted House first appeared on TV in the mid 1960’s. The commercial features a spooky announcer and two children playing with and truly enjoying the houses many amazing features. The toy boasts a jumping cat, a witch behind the opening front door, a ghost floating in the air behind a lighted window, a scary window shade, a shaking roof with banging shutters, a spooky, eerie sound and a frightening loud whistling noise. All of these features are operated by buttons and 3 ‘D’ cell batteries. Other available parts we make for this toy include the witch behind the door, the standing black cat, and the gray plastic buttons. Please watch for the Marx Hootin’ Hollow Haunted House to appear in stock at Uncle Al’s Toys!
-
This is a real, metal replacement battery box for the Cragstan Mr. Robot toy. It comes complete with the contact boards with new contacts and installs exactly like the original.
-
A nice Alps Windup Proud Peacock. The toy is all tin with rubber feet. When the toy is wound, the peacock walks and spreads his fan. He works wonderfully and would be a very nice addition to your tin toy collection.
-
Very RARE, Carolina Best 'Space Walking Dogs' counter card display from the late 1960's. This counter display has all 24 originally bagged and stapled ramp walker dogs still hanging in place after nearly 50 years and looks incredible in your man cave, woman cave, home or office. Only one very unique color dog stands out from all the others . . . just amazing! I loved this item when I first discovered it. Brought back MANY fond childhood memories! How many of you remember that Lays Potato Chips put these Space Walking Dogs in their bags of chips as a promo give away?? Gosh I'm old . . . but never too old to play!
-
Replacement Battery Cover for the Marusan Cadillac This listing is for a tin replacement battery box cover for the battery operated version of the Marusan Cadillac. The cover is often found missing from the Cadillac cars since the attachment is not permanent. As you can see, this new cover fits perfectly and looks great! A side by side comparison shows very slight differences between the two covers. My replacement has a larger piece of electrical board installed and the tongue latch is a bit longer for a better hold to the car. We prime the cover before finishing it with an automotive lacquer that matches the Marusan black color. The painted cover is then given a final polish. Just remove the cover from the packaging and install it on your car. Absolutely no disappointments with this part!
