-
Beautiful Bandai BMW Isetta friction powered vehicle in excellent original condition. Friction motor is sound and firm as new and the toy features a realistic opening front end to enter the vehicle.
-
A hood ornament replica for the Bandai Lincoln Convertible/Coupe. The replica is cast from an original ornament and fits exactly like the original installation. These are in stock and ready to go. *PLEASE NOTE* You may have to disassemble the toy in order to install this part, depending on whether or not the original emblem was pulled completely out or snapped off. If a piece is still showing on the top of the radiator shell, you can carefully trim the emblem base with an Exacto knife and push the remainder of the shaft through the hole. The new ornament can be glued in place rather than opening the toy.
-
Bandai Rolls Royce Silver Cloud 'Flying Lady' hood ornament replica, faithfully reproduced to fit exactly like the original installation. I cast my replica from an original ornament. Unlike the replacements offered by my competitors, my 'Flying Lady' still has her head . . . *PLEASE NOTE* You may have to disassemble the toy in order to install this part, depending on whether or not the original emblem was pulled completely out or snapped off. If a piece is still showing on the top of the radiator shell, you can carefully trim the emblem base with an exacto knife and push the remainder of the shaft through the hole. The new ornament can be glued in place rather than opening the toy. These are in stock and ready to go!
-
Without a doubt, one of the RAREST and coolest space toys ever made. 1960's Bandai Sears Radiation Tester Exclusive Area battery operated toy in nice working condition. This toy was available ONLY through Sears and could be found in their 1961 catalog. It operates on two 'D'cell batteries and features Bump N Go action, opening rear bay doors, a smoky fog emits while the radiation tester unfolds and lifts out of the bay. The arm retracts back into the bay and the doors close and the toy is on it's way again. During the entire cycle, the light pods in the rear flash red and green intermittently and are very bright. This early Japanese tin toy is a highly sought after space toy example and is sure to please. As can be seen in the pictures, the toy is in working condition and shows playwear and no paint touch ups. The battery compartment is very clean. This is a sizable toy stretching 21 inches in length, 5 inches wide and nearly 6 inches tall to the top of the antenna. Uncle Al's Toys is the only maker and provider of replacement parts for this toy. Both toys available here have replacement light pods, large antenna and front sight. Also included but not shown is a wonderful, first quality reproduction box, also available nowhere else! A great old vintage battery operated space toy that makes an outstanding functioning shelf piece display. This is not one to miss!
-
A new replacement seat for the Bandai Silver Pigeon Scooter. Molded and cast from an original seat so the shape and diameter are a perfect fit. The rubber hand grips for this toy are also available.
-
This is a replacement WIND UP KEY for the CIJ Alfa P2 Racer , made in France. All dimensions for the replacement were taken from an original key. The brass shaft diameter and the steel winding handle are of the same thickness as the original key. The length is correct and allows winding without interference or binding near the back wheel of the toy. If you look closely at the pictures, I also drilled and inserted a brass locking pin which secures the handle to the shaft, just as original. These can be ordered with black painted steel winding handle or aged patina. Please specify when ordering. These are in stock in both variations shown here. Make your Alfa complete with one of these rare keys.
-
This is a real, metal replacement battery box for the Cragstan Mr. Robot toy. It comes complete with the contact boards with new contacts and installs exactly like the original.
-
Cragstan Mr. Robot Replacement Eyes. This is a set of replacement eyes for the Cragstan Mr. Robot. These easily glue in place with just a couple drops of super glue.
-
Daiya Japan Martian Supersensitive Radar Jeep - These are replacement windshield domes for the Daiya, Martian Supersensitive Radar Jeep. Sold as a set of two for a perfectly matched set and best look.
-
Dan Dare SS Eagle Spaceship Canopy for the tin friction rocket from Mettoy of Great Britton. This replacement canopy is an exact copy of an original toy part and is produced in amber tint. The canopy is a removable toy part that allows for flint sparking replacement. This new part contains all of the original flaws of the master part and looks tremendous! Uncle Al is the only toy specialist making this part in amber tint to match the original! Just snap it on and you're good to go.
-
A new flexible plastic square tip propeller for the Cragstan or Yonezawa battery operated DC-7c aircraft toys. The perfect solution to those old broken or glue covered propellers. Our new prop is a bit more flexible than the original. Please note the wings must be disassembled in order to correctly install these propellers.
-
This brand new replacement seat for the Doepke Model Toy is created from a mold taken of an original toy part and is guaranteed to fit perfectly. The seat has the same bosses with a drilled hole to accommodate screw on fastening just like original. The seat should be washed with soap and water to remove mold release agent before painting or adhering cloth. This seat is available no where else but here and is in stock.
-
Made exactly like the original, this tin tower will fit perfectly should your Space Station be lacking. My tower also comes with the drive wheel and shaft for the large plastic antenna dish. (sold separately) This tower is used on both the red and blue versions of this toy.
-
Ichiko Space Patrol Car Astronaut Driver Head - This is a replacement replica tin head for the Ichiko Space Patrol Car. I fabricated my first one of these from pictures of the original. They are comprised of four pieces, front and rear of the helmet, inside face and outer earmuffs and strap. I have since acquired an original head and have created new tooling so that my replacement head is now near perfect! I also replicate the windshields and frames for this toy which run $175.00. These take about 4 weeks to complete from the time of order.
-
A replica hand crank for the 1950's Ideal Atomic Machine Gun. Created from a mold taken of an original toy part, it is stronger than original because I solid cast the square end that fits into the gun. I also solid cast the pin for turning the crank. The fit is tested on my own toy to ensure accuracy. I still resin cast my part but I designed it to be solid with the exterior look of the original. Please ask if you're looking for or need custom parts!
-
Irwin 'Man From Mars' Replacement Bubble Helmet A two piece bubble helmet for the Irwin 'Man From Mars' wind up toy from the 1950's. The helmet comes in two pieces as shown and installs just as the original. There are 4 alignment pins on one helmet half and 4 corresponding holes on the other half. A small bit of super glue to each pin will secure the helmet to the spaceman. There is a hole in the top of the helmet for the rubber antenna, which is also available here on this site. Many of the original bubbles are missing, cracked and re-glued or have become clouded or crazed from age. My new bubble is guaranteed to be an excellent fit and remain clear for years to come!
-
A replacement hat brim for the Strauss Jenny The Balky Mule Wind Up Toy.
-
Kanto Battery Operated Space Patrol - Replica Tower and Radar Dish, available ONLY through Uncle Al! - You won't find a more accurate, perfect fitting replica tower anywhere else. An outstanding original was borrowed for reference in the dimensioning, fit and color of this replica and it installs just as the original - an easy installation that you can do yourself with my instructions. The Kanto Space Patrol vehicle is one of the most highly sought after space toy collectibles and many times is missing this critical detail part. My re-creation is made exactly like the original 10 piece part. It comes painted in the correct colors and installs in minutes. This part is hand made to order, so please allow a minimum of two weeks for assembly prior to shipping. Another fine part available nowhere else!
-
Kanto Space Patrol Friction version replica cannon expertly crafted for a perfect fit.
-
Here we have a Convertible Replacement Windshield for the Marx Dick Tracy squad car. This is a brand-new replacement windshield for the 1950's 20" tin Marx Dick Tracy squad, Marx Army Command and Fire Chief friction drive cars. The windshield is created from a mold taken of an original 6 PIN windshield. This windshield will also fit the 4 PIN vehicles simply by removing the second pins from the ends. The convertible replacement windshield is fitted to a tin vehicle during the curing process for a guaranteed excellent fit!
-
A new replacement RED LENS for the large 20" Marx friction cars with Electric Siren lights. The lens will fit the Marx Dick Tracy Squad Car, the Army Command Car and the Fire Chief Car. This lens is an exact copy of the original and is made to function exactly the same.
-
A replacement gun tip for the 1950's Marx Captain Space Solar Scout Rifle. We create parts from a mold taken of an original toy part cast in urethane. It is as close to an injection molded original toy part as you can get. It is NOT a 3D printed part! The gun tip simply slides on to the end of your rifle. Install the screw and nut (not included) and you're done. The replacement tip is available in three Marx colors; red, green and blue. We test fit each part and guarantee the part to be a perfect fit.
-
Marx Captain Space Solar Scout Rifle REPLACEMENT CLEAR LENS. Crystal clear and screws on just like the original. Listing is for the CLEAR LENS ONLY, gun shown for identification and clarity only. These are in stock and ready to ship.
-
Marx Dick Tracy Squad Car / Army Command Car / Fire Chief Car replacement siren light. This fabulous replacement light is exactly like the original and comes completely wired with socket and bulb. Just attach and install as original. The rear housing can also be molded in olive drab on request but standard in stock is yellow/red
Copyright © 2024 Uncle Al's Toys. All rights reserved.
Website design and developed by Concept Infoway LLC