-
This listing is for a replica tin flag for the Masudaya 'Queen of the Sea' battery operated tin ocean liner. This tin flag is a nearly exact replica of the original, almost always missing tin flag that fits to the rear of the ocean liner. A shoulder is machined onto the shaft so the flag sits and fits at the appropriate height. Other parts are available for this toy such as the light blue radar antenna and the set of two clear dome light bulb covers. This great toy from the 1950's is such a nice, LARGE toy but many times nowadays when you find an example of this toy, it's missing some of these key, impossible to find pieces. Look no further, they're here at Uncle Al's!
-
Masudaya Queen of the Sea Replacement Light Domes, Set of TWO - This listing is for a set of TWO replacement light bulb covers for the Masudaya 'Queen of the Sea' battery operated tin ocean liner. These covers are and exact replica of the original toy parts and are guaranteed a perfect fit - just pop them on! Other parts are available for this toy such as the light blue radar antenna and the always missing rear tin flag. This great toy from the 1950's is such a nice, LARGE toy but many times nowadays when you find an example of this toy, it's missing some of these key, impossible to find pieces. Look no further, they're here at Uncle Al's!
-
Bandai Area Radiation Tester Replacement LIGHT POD, Left Hand GREEN is now finally available. These light pods were created from molds made of the original toy parts. The brass contacts for the light bulbs are hand made of the same thickness and configuration of the original parts. The same wattage bulbs are installed and colored as original. Ample wire is supplied and will be trimmed to length when you install. It should be noted that the pods are designed to be installed in the same fashion as the original parts. Some skill is required to open the tin pod pylons (not included - you must have the original pylons). The pods are secured to the pylon by brass eyelets with a minimum length of approximately 3/16". Once mounted, the wiring for each pod is trimmed to length and soldered to the pylon electrical mount pins. Be sure to apply electrical tape over the solder connections before reassembling the two pylon halves. The pods are also available as a set for a discounted rate of $250.00.
-
Bandai Area Radiation Tester Replacement RADAR DISH is a 3 piece part. The dish has a plastic backing, center plastic mount and a metal reflector. It attaches to the toy exactly as the original with holes for the mounting pin and extension arm. More parts are available for this toy.
-
Very nice Ha Ha Toys Astro Spaceman Robot in his original box is ready for action! Ha Ha Toys robots are known for having better quality gear systems than newer versions of this toy and are more sought after because of that. Batteries have been installed and the toy was hand tested for function and then promptly returned to the original packaging. Astro Spaceman Robot walks with swinging arms and his chest 'dash board' lights up. He works great and looks even greater when functioning! This toy comes in its original box with inserts. It was removed for these photographs only.
-
Bandai Area Radiation Tester Replacement LIGHT POD, Right Hand RED is now finally available. These light pods were created from molds made of the original toy parts. The brass contacts for the light bulbs are hand made of the same thickness and configuration of the original parts. The same wattage bulbs are installed and colored as original. Ample wire is supplied and will be trimmed to length when you install. It should be noted that the pods are designed to be installed in the same fashion as the original parts. Some skill is required to open the tin pod pylons (not included - you must have the original pylons). The pods are secured to the pylon by brass eyelets with a minimum length of approximately 3/16". Once mounted, the wiring for each pod is trimmed to length and soldered to the pylon electrical mount pins. Be sure to apply electrical tape over the solder connections before reassembling the two pylon halves. The pods are also available as a set for a discounted rate of $250.00.
-
Bandai Area Radiation Tester Replacement LIGHT PODS, L&R Set of two lights are now finally available. These light pods were created from molds made of the original toy parts. The brass contacts for the light bulbs are hand made of the same thickness and configuration of the original parts. The same wattage bulbs are installed and colored as original. Ample wire is supplied and will be trimmed to length when you install. It should be noted that the pods are designed to be installed in the same fashion as the original parts. Some skill is required to open the tin pod pylons (not included - you must have the original pylons). The pods are secured to the pylon by brass eyelets with a minimum length of approximately 3/16". Once mounted, the wiring for each pod is trimmed to length and soldered to the pylon electrical mount pins. Be sure to apply electrical tape over the solder connections before reassembling the two pylon halves. The pods are also available separately for $135.00 each. A discount savings is applied when buying the set of two and is reflected in this price of $250.00.
-
Perfect fit replacement rubber parts just like original! The rubber nose cone is cast to fit tightly but in the same contour of the rocket tip. The rubber fin tips just pop in. You may need to poke the old rubber bases out of the way to fit the base of the new tips into the holes. Make your XM-12 Moon Rocket a real show stopper again with these great replacement rubber parts. They are made of the same grade material as the original parts and can be installed without taking your toy apart. Also available for this toy are the crystal clear canopy. 'On/Off' ball switch and rocket engine celluloid windows.
-
Lincoln Continental Hood Ornament Antenna Set A reproduction tin and metal hood ornament/antenna combination for the Linemar 1956 Lincoln Continental tin cars. These parts are compatible with all versions of the Linemar Lincoln battery operated friction and remote control. The company liked to ship these parts separately from the toy and as a result, these parts were often lost. I fabricate the reproduction hood ornament exactly as the original with a large tab on the bottom side. This feature allows the hood ornament to insert easily into the slot above the grill. The reproduction antenna is the same as the original diameter of the shaft and fits correctly into the hole in the fender. The car in the picture is for display purposes only and is not for sale. These parts are now made to order. Please allow two weeks for delivery.
-
Replica Knockoff Spinner for Exclusive Sears Indy 500 Turnpike Racers Replica Knockoff Spinner for the Exclusive Sears Indy 500 Turnpike Racers - This listing is for new, white metal reproduction knockoff spinners for the Sears Exclusive battery operated Indianapolis 500 Race Car or the Sears Turnpike Line friction racer and the Sears Indy 500 friction racer. These three toys utilize the same master cast spinner but have different threaded diameters. The battery operated spinner has a smaller diameter hole than the friction cars so PLEASE SPECIFY which spinner you need when you purchase. The white metal castings are a bit softer and the wings are a bit thicker than the originals but as you can see, they look and work great. Holes come drilled and tapped so all you have to do is put them on your cars. Please also note that these are fabricated to mount on original car threaded studs. If someone has broken the original studs and replaced with an aftermarket screw, these will not work. When viewing the pictures, the white Indy 500 car is sporting the new knockoffs. The green Turnpike racer has original cast spinners. Note the larger mounting stud of the Turnpike car. These parts are in stock and ready to go.
-
Marx Hootin Hollow Haunted House Witch is a perfect reproduction of the original toy part. The replacement made from tin, decorated and mounts to the door just like original! Marx Hootin Hollow Haunted House can be seen in a mid 1960's TV commercial featuring a spooky announcer and two children playing with the house. The actions are triggered by pressing the buttons on the side. A jumping cat, a witch behind the opening front door, a ghost floating in the air behind a lighted window. A scary window shade, a shaking roof with banging shutters, a skeleton that jumps out of the chimney. A spooky, eerie sound and a frightening loud whistling noise. All of these features are operated with 3 'D' cell batteries.
-
This is an item that I've needed to make for some time and finally have it ready for purchase. The Bandai Volkswagen Bus battery operated version has this delicate, rear opening door that is so often missing from these toys. I had a toy with a damaged original door that I was able to recreate in tin to look and function just as original. This new tin door comes as shown in white automotive primer for $95.00 USD and can be finish painted in either RED or CREAM IVORY as the two original toy color versions that were available for an additional $25.00. It also comes with the hinge pin for mounting the door to the vehicle. This is an absolute must have if your bus is missing its rear hatch door and it is available no where else!
Copyright © 2024 Uncle Al's Toys. All rights reserved.
Website design and developed by Concept Infoway LLC